Search


Information

Products: 58
Categories: 13
Prices: British Pounds
Language: English

Language

Currency

pir model hard wired

pir model hard wired

Product Information

Turns your water on ONLY when you are at home.
THE PIR MOTION WATER CONTROLLER  
(CABLE HARD WIRED CONNECTION)
 
 
 
THE CONTROL BOX
 
Click HERE for technical specification. 
 
Control box measures 150 x 90 x 50mm can be installed flush or surface mounted
 
 
 
                    
                                                          The PIR MOTION SENSOR                         THE FLOODCHECK VALVE
When fitted the PIR device will  drastically save water and damage to property in homes office and factories.
 
The most  serious  damage  is when leaks occur and  the premises are vacant.
Sometimes for a few hours , sometimes for days or weeks.
 
If the water supply is  turned off.. the leak will not occur  ( see note below).
 
There is normally no need for the water supply to be on when the premises are vacant. 
 
The  Motion sensor water control will turn off the water after a short while if no movement ( or personal) is detected in the premise.  As soon as they return the water will come back on.
Two models are available. One connects the Motion detector (PIR)  to the control box  by two core cabel  supplied in the kit.
The other more expensive model uses wireless (radio) to connect the unit together. Otherwise they are the same.  
This model shown  is THE BASIC MODEL and contains  ,  control box, the valve,  power supply. and emergency lead, 3 meters twin core cable for connecting up the pir to the control box..and powerful rare earth magnet to protect the unit against limescale and metal object.
 
The PIR can be connected to the control  box by normal two core cable, or  we can supply  a model with  wireless ( radio) facility. The sensor can be fitted anywhere, and you can have as many sensors as you need. Typical only one is needed by the normal entry tom the premises. A second one upstairs might be useful.
 
This is how it works.
 
A solenoid valve (supplied) is fitted in line with your main water supply in your house. It is normally shut so the water is  normally  off  in your house . Near  to the main  entrance  of your home you fit  a small motion detector (PIR) ( supplied) ,similar to  the ones  used on burglar  alarms .
When the P.I.R.  detects movement   it will  send  as signal to the control box,
this in return will send a signal to the valve to open it for a pre set period of time. 
You can set the time the valve then remains  open to suit  yourself.
 Factory setting are ONE  hour.  You can select  time on  4 minutes to 3 hours.
Time options are 4mins, 30 mins, 1 hour,1.5 hours,2 hours 2.5 hours,3 hours , 3.5 hours , and auto quick select buton for long periods 6 or 8 hours
The control box has a long period ( one off) override buton . Useful for watering the garden or if you want to take advantage  of lower tarrif electricity  rates at night times for the dishwasher or washing machine.
 
The four minute setting is ideal for unattended  factory / offices toilets, wash rooms etc.
 
As long as anyone is moving in the area of the sensor the water will remain on . 
 When  you vacate the premises, or go to bed,  the water will go off after your preset time.
( say two hours) 
You can fit as  many  Sensors  as you need. For a small house only one is needed by the main entrance. If you have pet we can supply a special sensor that will ignore  pets under a certain size ( 25Kilo mass) .So your cat or dog won't be turning your water on and off when your not at  home. Or you can instll the snor at a hieght ab ove the pets. ( ask about per nuisance  sensors)
If you feel you need another sensor upstairs you can purchase  an additional PIR sensor  which is either connected by a two core cable or can be Wireless model if you have the wireless control box.
 
When you return it will automatically turn the water back on. You can turn it  off if you want to water the garden for longer than ONE HOUR . When you leave the home you can push a button which will turn  off the PIR  almost instantly  to enable you to vacate without being detected and it will turn off the water. That way you don’t have to wait 2 hours for the water to go off after you vacate
 
Note: in the event of a power failure  the valve will remain in the mode it was prior to the power failure.( normally it would be off  .) so you could loose your water for the time the power is off.
However.. a small back up battery lead  is  supplied for emergency. This is plugged into a small  9 VOLT  PP3 battery. It replaces the power supply and will restore your water in 20 seconds. It is intended as a temporary measure only. Not supplied but available  at your local store
                                                             
 What about POWER CUTS? WOULD I LOSE MY WATER SUPPLY?

Floodcheck products  have now been maufactured for over 8 years . and have been tested by  water research  companies  and found to be very reliable, and is approved and recommended by them.

Many  thousand have been installed.The reliability is very very high. However..as with anything,.a failure or problem could occur. It is designed that in the event of a power failure ther Floodcheck will remain in the mode it was in prior to the power cut. Normally the mode would be so that the water is ON so you would not lose your water.

For complete peace of mind consider have a manual byepass fitted by your plumber .These are available  from us if a problem does occur, JUST LIFT THE LEVERS UP TO BYE PASS THE FLOODCHECK TEMPORARILY, andyou will  have you water back on.When the manual bye pass is operated the Floodcheck may be removed completely for examination or service, and you will still have your full water supply... but of course no protection.

                               

Bye pass kit is supplied as above ( but without the Floodcheck(r) valve

 
NOTE: Some installations may have water stored in tanks in the loft. Turning off the main water supply will not  stop leaks from this but will drastically reduce  the possible damage.
 
Remember you will also need pipe connectors to fit the valve to your pipes. 15 or 22mm. price is £9.50 per set of two. See accessories.
 
Please note: This product is not in full production yet so we are only able to supply limited stock. Please contact us for prices and details. ASK FOR DETAILS AND PRICES OF THE HARD WIRED  MODEL.
Makes sure you check with us to ensure you get the correct power supply for your country and the correct sizes ring magnet and  pipe connectors.
Click HERE for technical specification.
call 07803 071001 for help.0r FREEPHONE 0n 0800 357 97 98
Note:  UK  Postage and  VAT  are included in prices shown
 
Recommended Accessories:


15mm Push Fit Connector UK @ £9.50 (details)
15mm Push Fit Connector UK


22mm Push Fit Connector UK @ £9.50 (details)
22mm Push Fit Connector UK
Quantity:  Add to Basket

Shopping Basket

Your basket is empty.

Items in cart: 0

Total: £0.00

New Arrivals

15mm Flow Restrictor
15mm Flow Restrictor

Mailing List

Subscribe to our mailing list below:

Your Email




About Us | Contact Us | Dubai Agent | E.U.Members | Free Floodcheck | Frozen Pipes | Links | Privacy Policy | Protect | Save Water | Specifications | Stockist and installers | Terms | USA Visitors SpeedFreaks
Powered by CubeCart
Copyright Devellion Limited 2006. All rights reserved.